Rubber Testing Equipment

Product Details:

We are manufacturer of Fatigue Testing Machine.

Application and Operation:

• This machine is used to test the fatigue strength of materials and to draw S-N diagram by research institutes, laboratories, material manufacturers and various industries.
• This is a rotating beam type machine in which load is applied in reversed bending fashion. The standard 8 mm dia. specimen is held in special holders at its ends and loaded such that it experiences a uniform bending moment.
• The specimen is rotated at 4200 rpm by a motor. A complete cycle of reversed stresses in all fibers of the specimen is produced during each revolution.
• The bending moment is applied to a lever system and can be easily changed by moving a weight over the lever. The total number of revolutions at which the specimen fails are recorded by a mechanical counter.
• An interlocking system puts off the motor at specimen failure. Machine meets requirements of IS 5075-1969.

Features :

• Light weight, compact size, simple design
• Table model, no need of foundation
• Simple lever system for changing load
• Accurately calibrated as per IS 5075
• Calibration in Nm available on request.

Specification:

• Maximum bending momentKg-Cm200Bending moment adjustableKg-Cm30-200RangesI-Kg Cm

• 100-200Gripping dia of specimenmm12Testing dia of specimenmm8Rotating speedrpm4200Accuracy of applied bending moment
• ± 1%Digital counter No. of digits
• 8Power requiredHP0.5Main supplyA.C. 3 ph440 V,50 HzOverall size (approx.)mm1000 L,X,500 W X 600 HWeight (approx.)Kg100

Additional Information:

• Item Code: FTM-8
• Pay Mode Terms: T/T (Bank Transfer),D/P

Product Details:

The design & manufacture of Digital Spring Testing Machine for testing springs for both compression & tensile test. Rugged housing construction design. Suitable upper & lower compression plate of 90 mm diameter will be provided for keeping compression springs. For Tension spring suitable mounting arrangement will be provided optionally. We offer variety of models to test spring of 5 kg to 250 kg & can test spring having diameters of 50 mm & 150 mm free length.

Specification:

• Model / Capacity: FM-UST-30/50, FM-UST-250
• Maximum Capacity: 5 kg, 10 kg, 20 kg, 30 kg, 50 kg, 100 kg, 250 kg
• Type of Spring: Tension and Compression
• Free length of tension spring: 150 mm
• Diameter of compression spring: 90 mm
• Load Application: By top hand wheel
• Maximum Cross Head Travel: 100 mm
• Force Measuring Resolution: 1 gm, 10 gm
• Pitch: 3 mm
• Type of Construction: Single Column
• Elongation/Deflection: 1 ft scale(300 mm)
• Least Count: 1 mm

Grip:

• Compression Plate: 90 mm dia.
• Tension Grip/Hook: Optional
• Loadcell & digital Indicator: Microprocessor based indicator suitably calibrated

Options Available:

• Elongation Measurement: Dial gauge with a least count of 0.01 mm or digital vernier with a least count of 0.01 mm can be provided.
• Digital Encoder

Additional Information:

• Item Code: FM-MF

• Capacity: 50/100/250/500/1000kgsFor various Material testing like :
• Rubber, Latex : Peel, Adhesion & Bond Test
• Wood, Plywood : Nail Withdrawal
• Paper : Tape, Cardboard, Adhesion & Peel Test
• Textiles : Fibre, Yarn, Thread & Fabric
• Plastic, Teflon, PVC & Rexins
• Composites, FRP & Ceramics.
• Steel
• Ferrous & Non-Ferrous Metals

Additional Information:

• Item Code: FM-DTTM
• Minimum Order Quantity: 1 Unit

Specification:

• High Density Accuracy: 0.001 g/cm3
• S.G. Range: 0.9 to 25
• Least Count: 0.001
• Eliminates calculation & manual error

Additional Information:

• Minimum Order Quantity: 1 Piece

The Abrasion Tester is used to evaluate the resistance of elastomers to frictional wearing Abrasion tests to this testing standard are performed on samples of materials which undergo wear and abrasion during their normal working life(e.g. tyres, conveyor and drive belts, shoesoles).The machine is as per DIN-53516.

Specification:

• Weight: 30 kg
• Power: 220 V
• Machine Dimension: 30*43*30 cm

Additional Information:

• Item Code: FM-AT
• Minimum Order Quantity: 1 Unit

The Shore Hardness is defined as the resistance to penetration by an indent or of specified shape under a defined load.Shore Hardness tester are available in various models for testing Vulcanized Rubber, Plastic, Ebonite, Fibre and all other soft and Hard Elastomers as per latest American Std ASTM-D 2240 and German Std DIN 53505.Shore A are suited for use on soft elastomers the hardness of which is between10 and 90 Shore A.Shore D are suited for use on harder elastomer (hardness >80 Shore A) and on plastics the hardness of which is between 30 and 90 Shore

Additional Information:

• Minimum Order Quantity: 1 Piece

The Shore Hardness is defined as the resistance to penetration by an indentor of specified shape under a defined load.Shore Hardness tester are available in various models for testing Vulcanized Rubber, Plastic, Ebonite, Fibre and all other soft and Hard Elastomers as per latest American Std ASTM-D 2240 and German Std DIN 53505.Shore D are suited for use on hard plastics of wh ich is between 10 and 90 Shore D.Shore D are suited for use on harder elastomer (hardness >80 Shore A) and on plastics the hardness of which is between 30 and 90 Shore

Additional Information:

• Minimum Order Quantity: 1 Piece

The Shore Hardness is defined as the resistance to penetration by an indentor of specified shape under a defined load.Shore Hardness tester are available in various models for testing Vulcanized Rubber, Plastic, Ebonite, Fibre and all other soft and Hard Elastomers as per latest American Std ASTM-D 2240 and German Std DIN 53505.Shore A are suited for use on soft elastomers the hardness of which is between10 and 90 Shore A.Shore D are suited for use on harder elastomer (hardness >80 Shore A) and on plastics the hardness of which is between 30 and 90 Shore

Product Code:FM Shore A

Additional Information:

• Minimum Order Quantity: 1 Piece

We are offering a wide range of Shore A Full Round which is defined as the resistance to penetration by an indentor of specified shape under a defined load. Shore Hardness tester are available in various models for testing Vulcanized Rubber, Plastic, Ebonite, Fibre and all other soft and Hard Elastomers as per latest American Std and German Std DIN 53505. Shore A are suited for use on soft elastomers the hardness of which is between 10 and 90 Shore A. Shore D are suited for use on harder elastomer (hardness > 80 Shore A) and on plastics the hardness of which is between 30 and 90 Shore.

Features:

• High strength

• Longer working life

• Perfect design

Additional Information:

• Minimum Order Quantity: 1 Piece

Specifications:

• LCD Display: 4 digits, 40 x 18 mm (1.57 x 0.71 inch)
• Measuring Range: 0 ~ 100 HD
• Resolution: 0.5 HD
• Power Supply: 1 x SR44 button cell battery (included)
• Item Size: 87 (L) x 56 (W) x 25 (D) mm (3.43' x 2.20' x 0.98' inch)
• Item Weight: 136 g (4.79 oz)

Additional Information:

• Minimum Order Quantity: 1 Unit

The Shore Hardness Tester A with Stand is defined as the resistance to penetration by an indenter of specified shape under a defined load. Shore Hardness tester is available in various models for testing Vulcanized Rubber, Plastic, Ebonite, Fibre and all other soft and Hard Elastomers as per latest American Std ASTM-D 2240 and German Std DIN 53505. Shore A are suited for use on soft elastomers the hardness of which is between 10 and 90 Shore A.

Specifications:

• Hardness: 10 and 90 Shore A.
• Value of Durometer: 100+/-0.5 HA
• Type: A
• Mounting: Bench Top

Additional Information:

• Minimum Order Quantity: 1 Unit

Specification:

• Measuring range: 0 - 100 Shore D units
• Measuring force: 4.45-44.5 N
• Depth of indentation: 0 - 2.5 mm he testing material has to be thicker than 6 mm)
• Test pressure: 50 N
• Dimensions: 115 x 60 x 25 mm
• Weight: 200 g (net); 300 g (gross)

Additional Information:

• Item Code: ASTM-D2240

International Rubber Hardness Degree Meter is used to determine the Hardness of Rubber components where highly accuracy and reliable determination of the Hardness is of extreme important. The principle behind the determination of hardness by dead load apparatus is based on the measurement of the difference between the depth of indentation of a standard ball into the rubber under a small contact force and a large
indenting force. This type of hardness determination is widely accepted by I.S, B.S and I.S.O specification.

Specification:

• Ball Diameter: 2.5 mm
• Contact Force: 0.3 N
• Total Force: 5.7 N
• Thickness: 4 mm

Additional Information:

• Item Code: FM-IRHD
• Minimum Order Quantity: 1 Unit

Specification:

• Power: 220 V
• Weight: 178 kg
• Size: 53*69*140 cm

Additional Information:

• Item Code: FM-Flex
• Minimum Order Quantity: 1 Unit

Product Details:

Hydraulic Press Dumble die cutter is used to cut the standard test samples of rubber used in rubber industries. We obligated to meet the quality standards of customers requirement.

Specification:

• Weight: 70 kg
• Specimen Diameter: 29.5 mm
• Drop Height: 10 mm

Additional Information:

• Item Code: FM-Resilience
• Minimum Order Quantity: 1 Unit

Compression Set Apparatus for testing under constant strain plates type with the base plate and hand wheel arrangement consists of 4 steel plates with flat and parallel ground faces. These plates are moving in a fixture having the rigid base plates guided on a pair of rods. The spacers are also guided on the same rods with springs in between to increase the space between the plates for inserting the specimen. The machine is as per I.S.3400 (PART 10)1977.

Specification:

No. of specimen tested: 3

Size of stainless steel plates: 45 x 10 x 130 mm

Size of spacers: 30 mm diameter x 9.40 mm

Additional Information:

• Item Code: FM-CSA
• Minimum Order Quantity: 1 Unit

Product Details:

Tension set is defined as the proportion of applied strain remaining after a test piece has been stretched and allowed to retract in a specified manner.It is determined by stretching a test piece of standard dimensions to a suitable length in the apparatus for a specified time and temperature and then allowed to recover. The tension set is calculated as percentage of initial strain.The machine is as per I.S.3400 (PART 13)1972.

Additional Information:

• Item Code: FM-TSA